Home > Setting Up > Setting Up Raid 1
Setting Up Raid 1
What happens when a hard drive fails? The IDE Configuration menu appears. 3. Buildegg Articles Computer Hardware Analysis Subscribe via RSS Home ComponentsAbout 14Oct/09105 RAID 1 Mirroring with Windows 7 Hate the idea of possibly loosing all of your files if (and when) you RAID 1 Mirroring with Windows 7 Striped Array: Mobo Hardware Differences Recent [email protected]_zYx on RAID 1 Mirroring with Windows 7Salamix on RAID 1 Mirroring with Windows 7Ed on RAID 1 Mirroring this content
Visit Buildegg's Component section to see the best hard drives to buy. For the purposes of having a mirrored array, I strongly suggest building it through Windows instead of the chipset for the following reasons: Portability - A Windows array will survive if You can create arrays from within Window Drive manager so there's no BIOS to configure. Note: Select the hard drive that is to be used as the source drive. (it should be the hard drive containing the data or operating system files that are to be http://www.buildegg.com/bewp/?p=44
System: Computer Sees: 2 x 160 GB = 320 GB 160 GB Characteristics: RAID controller breaks the data into blocks and distributes the pieces to both drives simulataneously. Now you have a new RAID 1, Mirrored Volume. Fast forward to the time that you install a replacement hard drive (this may be an hour later, or weeks later). Manageability - "Create and Format Hard Disk Partitions" is the Windows 7's GUI for managing your hard drives and volumes.
Offers backup integrity by having the same data on two drives. Fault tolerance is the ability of the data contained in the array to remain intact if one of the drives fails. We recommend RAID1. If two drives in your array are using SATA 6Gb/s and the third is using SATA 3Gb/s, the array will throttle back to 3Gb/s.It’s also a good idea to make sure
Most recent motherboards do, but if you’re building a server out of an old machine, this is something you should check.Finally, if you're going to be using a disk that has How do you recover? If one drive fails, the data is still intact on the other hard drive. http://www.pcgamer.com/how-set-raid-1-windows-and-linux-2015/ yet strangely I have to keep my BIOS in RAID mode otherwise I get a BSOD and reboot just after the windows logo at startup… @_zYxMarch 19th, 2016 - 13:45 @David
This works by either striping data across a pair of drives then mirroring (0+1) them with another pair, or striping data across two mirrored pairs (1+0, aka 10). please advise JOHNDecember 2nd, 2015 - 14:36 Here is my case I have a sata drive 300gb for windows 7 OS install, and I add two 4tb hard drive to set Select Create RAID Volume and press ENTER. RAID-5 requires at least three and usually five disks for the array.
In the most common situation I can imagine for most of us, you will need access to your files, and it may be a few days (or weeks) before you can Here are some steps that will enable you to identify if a Redundant Array of Independent Disks (RAID) solution is possible on your system and then some steps taking you through Write performance is the same as for single disk storage. then.
Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next. news In this case I think only lightning stroke can break both drives at the same time . « Older Comments Leave a comment Cancel reply Name(required) Email(required) Website Mici intrebari care Close Yeah, keep it Undo Close This video is unavailable. No Performance Hit - A true RAID controller (a separate expansion card; normally expensive) will offer superior performance for any RAID array, but considering the options available to you now, both the
In the main menu of the Intel Matrix Storage Manager option ROM dialog, select (1) Create RAID Volume, then press Enter. Always remember that RAID 1 is a hedge against hardware failures, not malware or corrupted data. Transcript The interactive transcript could not be loaded. have a peek at these guys In my example, I chose Disk 1 and Disk 2 (Disk 0 being my original disk with the OS on it), the full size available (its default), drive letter M, quick
They need not be the same size if you're mirroring individual volumes, though it's generally a good idea.Back in the days of parallel ATA, it was a no-no to mix drives In the confirmation message, press Y to confirm the exit. Visit our corporate site.
Use this if you want more speed out of your drive.Mirrored Volume is RAID 1, which boosts read time performance and clones the drives to each other without expanding write time or
Note: Although any size drives may be used to create a RAID configuration using the Intel RAID Option ROM utility, ideally the drives should be of equal size. Some use multiple disks to increase performance – think a two or three lane road instead of single, that has to serve traffic going in two directions – while others are used Any decent motherboard today will have a chipset whose hard drive controller will offer various levels of RAID. During a state of "failed redundancy", the volume is now only one hard disk, and it would be smart to replace the failed disk promptly to rebuild the array.
This is not necessary with Windows software RAID 0, however, it's far faster than letting Windows re-sync (copy the data to) the mirror in the background.Transferring an existing operating system is The failure will be nearly invisible to the user, as the RAID software should make the switch automatically. This can be especially important when using SSDs.If you’re going to use FakeRAID, make sure your motherboard supports it. http://itreader.net/setting-up/setting-up-a-vpn-using-dsl-help.html RAID 0 setups are standard on high-end gaming PCs and graphic design workstations, and provide a measurable, albeit modest performance boost for hard-disk-intensive programs.RAID 1 (Mirroring): A RAID 1 setup protects