Home > Searching For > Searching For An Internal Hard Drive For Dell Optiplex GX110
Searching For An Internal Hard Drive For Dell Optiplex GX110
If the drive you just installed is the primary drive, install your operating system on the hard-disk drive. Trace the one wire back to where it plugs in to the mainboard, as Synergy513 described above. Back to top #5 synergy513 synergy513 BC Advisor 938 posts OFFLINE Gender:Male Location:Florida Local time:02:59 PM Posted Yesterday, 01:24 PM Oh yes, the old power up with fans and hdd Now, if by some miracle, this is a tiny computer, with a PCMCIA hole on the front, then by all means buy one of these. navigate here
Removing a Hard-Disk Drive From the Hard-Disk Drive Bracket 1 Drive 2 Drive bracket 3 Screws (4) Secure the new drive to the drive bracket with four screws (see Figure 3). Disconnect the power and interface cables from the diskette drive and CD-ROM drive (if any). If you are placing a drive in the 1.6-inch slot, use the four screw holes in the side of the bracket. I had to reinstall Vista again, but other than that it's working great. https://forums.techguy.org/threads/searching-for-an-internal-hard-drive-for-dell-optiplex-gx110.489907/
With the two EIDE interface connectors on the system board, your system supports up to four EIDE devices in the mini tower chassis; the small-form-factor and low-profile chassis support up to Turn on the computer system. If you are installing a drive in the 1.6-inch bay, use the four screw holes in the side of the bracket (see Figure 13).
as stated abve, the power supply is first. Connect a power cable to the power input connector on the back of the drive, and connect one of the device connectors on the EIDE cable to the 40-pin interface connector NOTE: On systems with hard-disk drives larger than 2 GB, create a primary partition of 2 GB and divide the remaining capacity into partitions of 2 GB or less. Back to top #10 dc3 dc3 Arachibutyrophobia Members 27,541 posts ONLINE Gender:Male Location:Sierra Foothills of Northern Ca.
Inserting the Drive Bracket in the Chassis 1 Drive-cage slide rail 2 Chassis slots 3 Hinge tabs 4 Sliding tabs NOTICE: You must match the colored strip on the EIDE cable That looks like a good fit for the AT-2701FX. (View with Flash) http://support.dell.com/support/edocs/systems/op980/en/sm/MT/images/TD06_02.swf In that photo, you can see a red card. Advertisement Tech Support Guy Home Forums > Software & Hardware > Hardware > Home Forums Forums Quick Links Search Forums Recent Posts Members Members Quick Links Notable Members Current Visitors Recent Also, before you install a drive, see the other precautions in "Safety FirstFor You and Your Computer." If you are replacing a hard-disk drive that contains data you want to keep,
Moore's Law : 4d Graph in Progress Back to top #3 ranchhand_ ranchhand_ Members 1,142 posts OFFLINE Gender:Male Location:Midwest Local time:01:59 PM Posted Yesterday, 07:41 AM I don't think that http://newwikipost.org/topic/h6mZCsD9aDfDEBzoXUh3AigRGSHtxuq9/Error-on-Dell-Optiplex-Gx110.html Help Requests: If there is no reply after 3 days I remove the thread from my answer list. If it is not already connected, connect the blue end of the EIDE cable to the IDE1 connector on the system board (see Figure 9 in "Inside Your Computer"). Unpack the drive, and prepare it for installation.Check the documentation for the drive to verify that it is configured for your computer system.
NOTICE: When you unpack the drive, do not set it on a hard surface, which may damage the drive. check over here Stay logged in Sign up now! and then I plugged everything back in, and it booted up like new. These two pins are what sends the signal to power up.
Ideally, what you want with such a card, is a second faceplate in the box. You'll have to check first and see if any cards are already installed in there. If you are installing a drive in the 1.6-inch bay, use the four screw holes in the side of the bracket (see Figure 7).
If a hard-disk drive is already installed in the drive bracket, disconnect the power and interface cables from the drive.
Connect a power cable to the power input connector on the back of the drive, and connect an EIDE cable to the interface connector on the back of the drive (see When you connect two EIDE devices to a single EIDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable Check out our 'Quick ProLiant Quoter' page for a fast and easy way to search our HP ProLiant parts and Care Pack alternative support prices Get A Quote MENU 0845 3021922 The Dell documentation seems to suggest this same motherboard is used for both MT and DT.
Edited by dukejohn2000, 28 February 2017 - 10:23 PM. Local time:11:59 AM Posted Yesterday, 11:33 AM Please post the model of this Dell desktop. Reinstalling the Hard-Disk Drive Bracket in the Small-Form-Factor Chassis 1 Tabs on bottom of drive bracket 2 Hooks on chassis floor 3 Drive bracket 4 Release tabs (2) NOTICE: You must weblink Part Code Man.
Check all connectors to be certain that they are properly cabled and firmly seated. Unpack the drive, and prepare it for installation. It has a 32 bit connector, and is "universal keyed" and can operate at either 3.3V or 5V. In 2012 we shipped 11,600 refurbished items and had only 82 returned as faulty.Learn more IT Support Contracts Whether you are a small business, large enterprise, or government organisation with thousands
For instructions, refer to the documentation that came with your operating system. Back to Contents Page Jump to content Sign In Create Account Search Advanced Search section: This VAT 985 2208 02. Attaching Hard-Disk Drive Cables in the Small-Form-Factor Chassis 1 IDE1 connector 2 EIDE cable 3 Power cable NOTICE: You must match the colored strip on the EIDE cable with pin 1 More About Us...
Sign up now!